Gas Dryer Repair in the Twin Cities
Gas dryers on every major platform — igniter, gas valve coils, flame sensor, thermal fuse, and high-limit thermostat service. We service gas ranges, ovens and dryers.
- 4.5★ · 900+
- 1-Yr Warranty
- OEM Parts
- Same-Day
Symptom triage
Match your symptom to the most-likely failure
Why us
What you get with every visit
FAQ
Questions we get every week
Do you service gas dryers?
We service gas dryers: the igniter, gas valve coils, flame sensor, thermal fuse and venting. Gas piping and shutoff valves belong to a licensed gas fitter or your utility, and we do not modify gas lines.
Most common gas-dryer failure?
Whirlpool / Maytag gas-valve coils — the pair fails together and stops the flame from lighting even though the igniter glows. $215–$325 for the kit, installed.
How much does gas dryer repair cost?
Most gas dryer repairs $225–$385 all-in including the $149 trip fee (credited toward the repair when you approve it). Igniter $185–$285. Gas valve coil kit $215–$325. Thermal fuse $185–$245. Flame sensor $185–$245. Belt + roller kit $245–$345.
NG to LP conversion?
Fuel conversions touch the gas supply, so they are referred to a licensed gas fitter. We can service the dryer's igniter, valve coils and burner before or after the conversion.
Same-day service?
Yes — we are open 7am–9pm every day, so call early for a same-day window. Igniters, gas-valve coils, thermal fuses, and belts ride on the truck.
What should I do if I smell gas near my dryer?
Leave the house right away, taking everyone with you, and do not touch light switches, the dryer or any other electrical device on the way out. From outside or a neighbor's home, call your gas utility's emergency line and 911. Do not go back in until the utility says it is safe. Do not try to find, tighten or repair a gas connection yourself.
A gas smell is never a normal dryer symptom, and it is not something a homeowner should diagnose. Once the utility has cleared the home, we can look at the dryer itself, such as the igniter, valve coils, flame sensor and venting. Work on the gas piping or the shutoff valve belongs to a licensed gas fitter or the utility. Central Minnesota Appliance Repair services gas dryers across the Twin Cities for problems with the appliance, not the building's gas system.
Gas dryer symptoms, likely causes and what we check
A gas dryer shares a drum, motor and belt with an electric dryer. The difference is how it makes heat, and that is where the extra parts live.
| Symptom | Likely cause | What we check |
|---|---|---|
| Drum spins, no heat, igniter never glows | Open igniter, thermal fuse or sensor fault | Igniter current, thermal fuse continuity, flame sensor |
| Igniter glows, burner never lights | Valve coils weak or failed, gas not reaching the valve | Coil resistance, valve operation, supply at the appliance |
| Burner lights, then shuts off quickly | Flame sensor, high-limit, or restricted exhaust | Sensor reading, thermostats, exhaust airflow |
| Dryer takes multiple cycles to dry | Lint-clogged vent, weak burner, moisture sensor | Vent airflow, flame strength, sensor reading |
| Clicking or ticking, nothing starts | Control or ignition fault | Control output, igniter circuit, door switch |
| Drum does not turn | Belt, idler or motor | Belt condition, idler pulley, motor |
| Exhaust smells unusual | Lint buildup near burner or vent restriction | Burner area, vent run, exhaust path |
Published prices for this page: most gas dryer repairs fall between $225 and $385 all-in. Igniter $185 to $285, gas valve coil kit $215 to $325, thermal fuse $185 to $245, flame sensor $185 to $245, belt and roller kit $245 to $345. The $149 trip fee is credited toward the repair when you approve it.
Why does a gas dryer need a clear vent more than an electric one?
A gas dryer burns gas to make heat, and the products of that combustion leave through the dryer exhaust along with the moist air from the drum. That means the vent carries exhaust gases outdoors, not just humid air. A vent that is crushed, clogged with lint or capped with a stuck damper can hold those gases back, and it also makes the dryer overheat and trip its safety devices.
This is one reason a gas dryer must always vent outdoors, never into a garage, basement or crawl space. Rigid or smooth-wall metal duct is the standard; foil or vinyl accordion duct traps lint and crushes easily. Keep the run as short and straight as possible. In Minnesota, long runs through cold attics or rim joists are common in older homes and tend to collect moisture and lint, which freezes and restricts airflow in winter.
Install a working carbon monoxide alarm near the sleeping areas and the laundry room if you own any gas appliance. If the alarm sounds, get everyone outside and call 911. A restricted vent, a heavy lint buildup or a damaged exhaust are reasons to schedule service before the problem escalates. Our dryer not heating page explains how venting and heat problems overlap.
What does a technician check on a gas dryer visit?
Our checks focus on the appliance, its ignition system, its safeties and its exhaust.
Ignition sequence
We watch the igniter glow, the valve coils open and the burner light, in order. Each step has a timing, and the point where the sequence stops tells us which part is failing.
Valve coils and flame sensor
Gas valve coils weaken over time. A weak coil may open the valve for a moment and then let it close, giving a flame that lights and goes out. The flame sensor and igniter are tested against their expected values, not replaced by guesswork.
Thermal fuse and high-limit
These safety devices cut heat when the dryer gets too hot. When one has tripped, we do not simply replace it. We find out why the dryer overheated, usually a restricted vent, before the new part goes in.
Vent and exhaust path
We check airflow at the dryer exhaust and look for crushed duct, lint buildup and a stuck exterior damper. If the run is restricted, we tell you what we found.
Appliance connection
We confirm the dryer is connected as it should be at the appliance. If anything about the gas supply or piping is wrong, we stop, tell you, and refer you to the utility or a licensed gas fitter. We do not modify gas lines.
Is it worth repairing an older gas dryer?
Usually yes, for the common parts. A gas dryer is a simple machine, and igniters, valve coils, fuses, belts and rollers are inexpensive compared with a new dryer. A drum that still turns freely on good rollers, with a sound cabinet and no rust, is a good candidate for a repair that buys several more years.
The decision tilts toward replacement when several systems are failing at once, when the drum or its support is damaged, when the cabinet has rust-through, or when the repair cost approaches the price of a comparable new dryer. A new dryer may also use less energy or have a better moisture sensor, which has some value.
Compare actual costs. Our dryer repair cost page and the appliance repair cost guide show typical figures, and we will tell you straight when a repair does not make sense. If you are considering switching fuel types, note that moving between gas and electric requires a different hookup, and the gas side must be handled by a licensed professional.
What can I check safely at home if my gas dryer will not heat?
Clean the lint screen and wash it with soap and water if it has a film, since dryer sheets can leave a coating that blocks airflow. Pull the dryer forward only as far as the connections allow, without stressing the gas line or the flexible connector, and check that the vent hose is not crushed behind it. Look outside at the exhaust cap and make sure the flap opens freely and nothing blocks it.
Do not touch, bend or disconnect the gas connector or the shutoff valve. If you have to move the dryer to clean behind it and you are not comfortable doing so without disturbing the gas connection, leave it and call. Do not use a dryer you suspect is leaking gas.
If the dryer takes much longer than it used to, clean the vent before assuming a part has failed. If it still does not heat after the vent is clear, schedule a visit. A gas dryer that makes a repeated clicking sound but no flame, or that smells of gas, should not be run again until it is checked.
More gas dryer questions
Does a gas dryer need a carbon monoxide alarm nearby?
A working carbon monoxide alarm is a good idea in any home with a gas appliance. Place one near sleeping areas and test it regularly. If it sounds, get everyone outside and call 911.
Why does my gas dryer click but not light?
Usually the igniter or the valve coils are the problem, or the control is not telling the burner to start. The test sequence shows which one, and the repair is typically a part swap.
Is it safe to run a gas dryer with a clogged vent?
No. A clogged vent traps heat and exhaust gases, raises the fire risk and can trip safety devices. Have the vent cleared before running it again.
How is a gas dryer repair different from an electric one?
The drum, motor, belt and controls are similar. The heat system differs: a gas dryer uses an igniter, valve and burner while an electric dryer uses a heating element. See our electric dryer repair page for that side.