LG Washer Error Codes
OE, UE, LE, IE, FE — What They Mean & How We Fix Them
LG front-load and top-load washers (WM, WT, WashTower) share an error-code table. The ones our Twin Cities trucks see most are OE (won't drain), UE (won't spin / unbalance), LE (motor / Hall sensor), IE (won't fill), FE (overfilling), and dE (door won't lock).
- 4.5★ · 900+
- 1-Yr Warranty
- OEM Parts
- Same-Day
Same-day windows
Call early for a same-day route.
Serving the Twin Cities
$149 trip fee, credited to repair.
EPA 608 certified
Sealed-system & refrigerant work.
1-year warranty
Parts and labor in writing.
Updated June 21, 2026
Quick answer
LG Washer Error Code Repair — Twin Cities — Quick Answer
What we fix in the Twin Cities
The Twin Cities repair mix
How to enter LG washer diagnostic mode
The button combination for LG's test mode differs by model and year, so confirm it in your owner's manual or on LG's Smart Diagnosis support page before you try it. Many LG models also support Smart Diagnosis: the washer plays a series of beeps that you hold your phone up to in the LG ThinQ app (or play to LG phone support) to read the stored fault.
Why the main board is rarely the first suspect
A code rarely means the main board has failed. OE is almost always the pump or a clogged coin trap, not the board. UE on a front-loader is suspension rods, not the board. LE1 on a top-loader is the Hall sensor mounted on the rotor, not the board. The main control board is the right call only after the wiring, sensors and motor have been ruled out. We test the inexpensive parts first.
LG washer repair in the Twin Cities
We stock LG drain pumps (with coin traps), inlet valves, door locks, pressure sensors, Hall-effect sensors, suspension-rod kits for WM front-loaders, and the common LG / WashTower main control boards on the truck. We serve Minneapolis, Saint Paul, Edina, and Wayzata and carry the common parts to finish many repairs in one visit. Flat $149 trip fee, credited toward the repair when you approve it. 1-year written parts-and-labor warranty.
Need appliance repair in the Twin Cities? Call 7am–9pm, every day.
FAQ
Washer repair in the Twin Cities: FAQs
What does OE mean on an LG washer?
OE means the washer couldn't drain in the allowed time. On LG front-loaders the cause is almost always a clogged coin trap (the small access door at the bottom-right front) — coins, bobby pins, and lint plug the impeller. Open the trap, drain to a shallow pan, and clear the impeller. If OE returns, the drain pump motor or a kinked drain hose is next. Most OE repairs run $245–$345 all-in.
What does UE mean on an LG washer?
UE (also shown as uE) is a load-unbalance code — the drum couldn't balance the load during the spin step. Single heavy items (bath mats, comforters) or small loads are common causes; re-distribute and run a Rinse + Spin. If UE keeps returning on normal loads, the suspension rods on a WM front-loader have worn (4-rod kit, $385–$525) or the dampers on a WT top-loader need replacement.
What does LE or LE1 mean on an LG washer?
LE / LE1 is the motor Hall-effect sensor or the direct-drive stator. On LG top-loaders LE1 is commonly the rotor position (Hall) sensor, a $285–$425 repair. On front-loaders LE can be the motor wiring or windings. We test the motor circuit and sensor before condemning the main control board.
How do I enter LG washer diagnostic mode?
The button combination varies by model and year, so check your owner's manual or LG's Smart Diagnosis support page. Many LG washers also support Smart Diagnosis: hold your phone to the washer while it plays its tone, and the LG ThinQ app reads the stored faults.
What does IE mean on an LG washer?
IE is an inlet-fill fault — water didn't reach the target level in the allowed time. Check that both hot and cold supply valves are fully open (a single-supply install will throw IE), clean the small screens at the back of the washer where the hoses connect, and check for kinked hoses. If supply is good, the inlet valve solenoid has failed ($245–$345).
What does dE mean on an LG washer?
dE (or dE1 / dE2) means the door didn't lock — the washer won't fill or spin without a confirmed lock. Open and firmly re-close the door; if dE returns, the door lock assembly's PTC has burned out ($245–$345 all-in). On front-loaders, a bent striker on the door is a common companion cause.
How much does LG washer repair cost in Minneapolis?
Most LG washer repairs land $245–$465 all-in. Door lock $245–$345. Drain pump $245–$345. Inlet valve $245–$345. Hall sensor $285–$425. Suspension-rod kit (WM front-loaders) $385–$525. Main control board (rare) $385–$525. The flat $149 trip fee is credited toward the repair when you approve it.
Why does my LG washer keep showing Sud or SUdS?
Excess detergent or non-HE detergent. LG front-loaders use roughly 1/4 the detergent of a top-loader (about 2 tablespoons of HE liquid for a normal load). Run a Tub Clean cycle empty with no detergent to clear residual suds, switch to HE-rated detergent, and use less than you think. Sud is not a parts fault.
Related repair pages
- LG washer repair →
- LG washer and appliance repair in Minneapolis →
- LG appliance repair (hub) →
- All LG error codes (Minneapolis) →
- LG refrigerator error codes →
- LG dryer repair →
- LG dryer not heating →
- Washer repair Minneapolis →
- Washer not draining Minneapolis →
- Washer not spinning →
- Whirlpool washer not spinning →
- Samsung appliance repair →
- Minneapolis appliance repair guide →
- Refrigerator repair Minneapolis →
What will this cost?
Pricing & repair-cost pages
Trying to decide repair vs. replace? These pages break down real Twin Cities pricing by brand, model class, and failure mode.
Book washer repair in the Twin Cities
Have your model and serial number handy. Call early and we can often get you a same-day window across the Twin Cities.
How do I know which LG washer code I am looking at?
Read the letters on the display exactly, including capital and lowercase. LG washer codes are two letters, such as OE or IE, and the case matters on a small panel. Then match them to the table below, and note whether you have a front-load or top-load model.
Central Minnesota Appliance Repair uses LG codes to decide where to start in Minneapolis, St. Paul and the metro. Most LG codes name the area, such as drain, fill, door or motor, and we confirm the part with a test before replacing anything.
LG washer codes, meaning and first check
These are the LG washer codes we see most and are confident about. If your code is not listed, call with your model number.
| Code | What it means | What we check |
|---|---|---|
| OE | Drain fault | Pump filter, drain hose, standpipe, pump |
| IE | Water inlet fault; the tub did not fill in time | Faucets, inlet screens, hoses, inlet valve |
| UE | Unbalanced load | Load position, level, suspension |
| LE | Motor fault | Motor wiring and rotor position sensing before any board |
| dE | Door not detected as closed or locked | Door seal, striker, lock assembly |
| PE | Water level pressure sensor fault | Pressure hose, sensor and connector |
| tE | Temperature sensor fault | Thermistor and wiring |
| PF | Power failure during a cycle | Not a fault; restart the cycle |
| CL | Control lock | Not a fault; hold the indicated button about 3 seconds to release |
| Sud / SUdS | Too many suds | Detergent type and amount; use HE detergent and run a rinse and spin |
Details by code: LG washer OE error, LG washer IE error and LG washer LE error. Codes vary a little by model, so confirm against your owner's manual.
Why does my LG washer show UE even with a small load?
UE means the drum could not settle for the spin. A small load can still be unbalanced if it is one heavy item, such as a bath mat or jacket, because the drum has nothing to offset it. Add a few towels or redistribute the load and try again.
If UE shows on normal loads, check that the washer is level on all four feet and that the shipping bolts were removed after delivery. A washer on an uneven basement floor can walk and fault out.
If level and loading are right and UE keeps returning, the suspension or dampers may be worn. That needs a technician. Do not lean on the washer while it is spinning to try to help it. Our $149 trip fee is credited toward the repair when you approve it.
Can I reset an LG washer code by unplugging it?
You can try once. Unplug the washer, wait a minute, restore power and run a short cycle. A one-time glitch may clear. If the same code returns right away, the fault is real and repeated resets will not help.
A drain code can leave water in the tub, and the door may stay locked. Cut power and drain the tub through the service hose before you open the door. Never force the door open with water inside.
A door or motor code should not be bypassed. Door locks are safety devices. If the washer has a persistent code, our technician will test the circuit and replace the failed part. See our washer repair page for what a visit involves.
More LG washer code questions
Is there a difference between front-load and top-load codes?
Many codes are shared, but some apply to one type. Tell us which you have when you call.
Where do I find my LG model number?
Look for the tag inside the door frame on a front-loader, or under the lid on a top-loader. Have it ready when you call so we can match the code to your model.
Does LG have a phone diagnostic?
Some models support an app-based diagnostic. Check your manual for the steps that apply to your washer.
Will a code damage the washer if I keep using it?
It can. Drain, door and motor codes should not be ignored. Stop using it until it is checked.