Maytag Washer Error Codes
F51, F50, F9 E1, F5 E2 — What They Mean & How We Fix Them
Maytag Bravos (top-load), Centennial (top-load), Maxima (front-load), and Maytag Commercial washers run on the same Whirlpool VMW / Cabrio / Duet control platforms — fault codes are nearly identical to Whirlpool. The ones our Twin Cities trucks see most are F51 (rotor position), F50 (motor circuit), F9 E1 (drain), and the common Bravos LF (long fill).
- 4.5★ · 900+
- 1-Yr Warranty
- OEM Parts
- Same-Day
Same-day windows
Call early for a same-day route.
Serving the Twin Cities
$149 trip fee, credited to repair.
EPA 608 certified
Sealed-system & refrigerant work.
1-year warranty
Parts and labor in writing.
Updated June 21, 2026
Quick answer
Maytag Washer Error Code Repair — Twin Cities — Quick Answer
What we fix in the Twin Cities
The Twin Cities repair mix
How to enter Maytag washer diagnostic mode
The service-mode button or knob sequence differs by model and control, so use the tech sheet that ships with the washer (usually taped inside the cabinet or console) or your owner's manual rather than guessing. Service mode runs the washer through inlet, drain, motor, door-lock and pressure-sensor tests and shows stored codes in the display.
F51 on a Bravos: rule out simple causes before parts
On Maytag Bravos washers F51 means the control lost track of rotor position. The cause is not always the sensor. A loose connector, debris around the basket, or a loose rotor bolt can produce the same code. The rotor bolt sits on the underside of the washer on the motor rotor, so checking it means tilting the washer back, which is a job for a technician. We check connections and the rotor first, then the position sensor, and the main board last.
Maytag washer repair in the Twin Cities
We carry common Maytag drain pumps, inlet valves, door locks, pressure sensors, motor control boards and rotor position sensors, and Maytag, Whirlpool, KitchenAid, Kenmore Elite and Amana parts are largely cross-compatible, so many repairs are finished in one visit. Flat $149 trip fee, credited toward the repair when you approve it. 1-year written parts-and-labor warranty.
Need appliance repair in the Twin Cities? Call 7am–9pm, every day.
FAQ
Washer repair in the Twin Cities: FAQs
What does F51 mean on a Maytag Bravos washer?
F51 is a rotor-position fault. The cause can be a loose connection, a loose rotor bolt or the position sensor, and the bolt is under the washer, so it is a technician check. Rotor or sensor repair runs $245–$425 all-in.
What does F9 E1 mean on a Maytag washer?
F9 E1 is drain time exceeded — clogged pump impeller, kinked drain hose, or drain standpipe restriction. On Maxima front-loaders open the pump access door at the bottom-right and clear the impeller. Repair $245–$365.
What does LF or LO FL mean on a Maytag washer?
Long fill — the washer couldn't fill in time. Confirm hot and cold supply are fully open, clean the mesh screens where the supply hoses connect, and check that the pressure-sensor air hose isn't pinched. Inlet valve failure if supply is good — $245–$345.
How do I enter Maytag washer diagnostic mode?
The sequence differs by model and control. Check the tech sheet that ships with the washer (usually inside the cabinet or console) or your owner's manual. Service mode runs the washer through each subsystem and shows stored codes.
What does Sd or F0 E2 mean on a Maytag washer?
Excess suds. Maytag HE washers use about 1/4 the detergent of an old top-loader. Run a Clean Washer cycle empty, switch to HE-rated detergent, use 2 tablespoons for a normal load. Not a parts fault.
How much does Maytag washer repair cost?
Most Maytag washer repairs land $245–$485 all-in. F51 rotor or sensor repair $245–$425. Door lock $245–$345. Drain pump $245–$365. Inlet valve $245–$345. Pressure sensor $225–$325. Shift actuator $285–$485. MCU $285–$525. Suspension rods (Maxima) $385–$525. The $149 trip fee is credited toward the repair when you approve it.
Are Maytag, Whirlpool, and Kenmore washer codes the same?
Yes — Maytag (Bravos, Centennial, Maxima), Whirlpool (Cabrio, Duet), KitchenAid, Kenmore Elite, and Amana all run on the same VMW (top-load) and Cabrio/Duet (front-load) control platforms. Fault codes and most parts are cross-compatible.
Related repair pages
- Maytag appliance repair (hub) →
- Maytag Bravos F51 error →
- Maytag Bravos F1 error →
- Maytag washer F21 error →
- Whirlpool washer error codes →
- Whirlpool error codes (Minneapolis) →
- LG washer error codes →
- Samsung washer error codes →
- Washer repair Minneapolis →
- Washer not spinning →
- Washer not draining Minneapolis →
- Minneapolis appliance repair guide →
- Refrigerator repair Minneapolis →
- Dryer repair Minneapolis →
What will this cost?
Pricing & repair-cost pages
Trying to decide repair vs. replace? These pages break down real Twin Cities pricing by brand, model class, and failure mode.
Book washer repair in the Twin Cities
Have your model and serial number handy. Call early and we can often get you a same-day window across the Twin Cities.
Maytag washer codes: meaning and what we check
Maytag washers share their control platform with Whirlpool, so the F-E pair codes below are common to both. Letters and numbers may be shown with or without a space.
| Code | What it means | What we check |
|---|---|---|
| F9 E1 | Drain problem; the washer could not empty in time | Drain hose and standpipe, pump filter or coin trap on front-loaders, pump impeller and motor |
| F8 E1 | Water is not filling as expected | Supply faucets, inlet screens, hoses, inlet valves, pressure sensor and its hose |
| F5 E1 / F5 E2 | Door-lock or lid-lock fault | Door or lid latch, lock assembly, strike alignment, wiring |
| LF | Long fill; the tub took too long to reach its level | Water pressure, kinked hoses, screens in the hose ends, inlet valve |
| F51 | Rotor position fault (Bravos top-loaders) | Connections, debris, rotor bolt, position sensor, then the board |
| F7 E1 | Motor or motor control fault | Motor wiring, motor control board |
| F1 | Main control board fault | Reset first, then the board and its connections |
| uL | Unbalanced load | Load position, level, suspension on front-loaders |
| Sd | Too many suds | Detergent type and amount; use HE detergent and run a rinse and spin |
Details by code: Maytag Bravos F51 error, Maytag Bravos F1 error and Maytag washer F21 error. Prices from this page: most Maytag washer repairs $245 to $485 all-in, drain pump repairs $245 to $365. The $149 trip fee is credited toward the repair when you approve it.
Can I reset a Maytag washer with an F-E code myself?
Yes, and you should try before booking. Unplug the washer for a minute, plug it back in, and run a short rinse or drain-and-spin cycle. A glitch that came from an interrupted cycle or a power dip often clears this way.
Before the reset, handle the hose and filter basics. Check that both water faucets are fully open. Pull the machine out, look at the hoses for kinks, and clean the mesh screens in the fill hose ends. Those screens pick up grit and scale. On a front-loader, open the small filter access at the lower front, put a towel down and clear the coin trap.
Never defeat a door or lid lock to get a cycle to run. Those locks protect you from a spinning drum. If the lock code returns, stop using the washer and call.
When is F9 E1 a failed pump rather than a clog?
F9 E1 becomes a part failure when the drain path is clear and the washer still does not empty. If the hose is free, the filter is clean and the standpipe drains a bucket of water quickly, the pump is next. A pump that hums but does not move water has a jammed impeller; a pump that makes no sound at all has a failed motor or no power. We test both before replacing anything.
Small items are the usual cause of the jam: coins, hair ties, underwire from bras and sock fragments. If you see these in the filter, it is worth checking what else is in the pump. If the standpipe backs up with another drain running, call a plumber, because the washer is not at fault. See also washer not spinning and washer not filling.
What does a Maytag washer service visit include?
Central Minnesota Appliance Repair reads the code, checks the symptom against it and tests the component before recommending a repair. You approve the quote first, and the $149 trip fee is credited toward the repair. Approved work carries a one-year written parts-and-labor warranty. Learn more on our Maytag appliance repair page.
More questions about Maytag washer codes
Is it safe to use a Maytag washer that shows a drain code?
Not until you find the cause. A washer that cannot drain may leave standing water and soaked clothes, and some models will not unlock the door. Check the hose and filter, then call if needed.
Why does my Maytag washer fill slowly?
Slow fill usually comes from a partly blocked screen, a kinked hose, low household pressure or a weak inlet valve. Clean the screens first.
Does the code stay stored after I unplug the washer?
Often it does not appear again unless the problem recurs, but the control may keep a history. A technician can read it during a visit.
Where do I find the Maytag model number?
Top-loaders usually have it inside the lid or on the back; front-loaders have it around the door opening. Photograph the label for the call.