FRIGIDAIRE · NO ICE

Frigidaire Ice Maker Not Working

Gallery, Professional & Standard — Real Fixes

Frigidaire ice makers (Standard, Gallery, Professional, and the older Pure Source models) have a well-known failure family centered on the ice maker module itself and the dual-coil inlet valve. Frigidaire's ice maker is mostly a self-contained module, so replace-the-module diagnostics are usually faster than rebuilding individual components.

Last reviewed November 16, 2026

Quick answer

Frigidaire Ice Maker Repair — Twin Cities: quick answer

What we fix in the Twin Cities

The Twin Cities repair mix

Freezer temp and water filter — start here

Frigidaire ice makers need a freezer ≤10°F to cycle. Verify with a thermometer at the back wall. Then check the PureSource / Pure Air filter status — past-life filters drop water pressure below the inlet valve's spec, so cubes come out hollow, half-frozen, or stop altogether. Filter $35–$55 (DIY). On a Gallery French-door model, see the Frigidaire Gallery ice maker guide for the module, mold thermostat and inlet-screen checks and costs.

On/off switch bumped off — check this first

The wire-bail or paddle on/off switch on the side of the Frigidaire ice maker is famously easy to bump when removing the bin. We confirm the switch is in the on position (down for wire-bail) before anything else. If it is only the switch, there is nothing to replace, and you can check it yourself first.

Fill tube freeze — winter-specific

The fill tube from the back of the freezer into the ice maker freezes solid in deep winter when (a) inlet pressure drops or (b) the inlet valve drips slow. Thaw the tube with a hair dryer on low heat, then replace the inlet valve to prevent recurrence ($185–$245).

Ice maker module — Frigidaire's signature failure

The whole ice maker module on Frigidaire fridges (cycles every 90 minutes when functional) can wear out the harvest motor or the internal thermostat with age. We test the module's harvest cycle; if the module fails to cycle, we swap the whole assembly. $245–$385 OEM installed.

Dual-coil inlet valve

Frigidaire fridges use a dual-coil inlet valve — one coil for the dispenser, one for the ice maker. One coil can fail while the other still works, so you may see dispenser water working fine but ice production stopped. We test coil resistance against spec before condemning. $185–$245 OEM installed.

Professional and Built-In specifics

Some Frigidaire Professional built-in refrigerators add a separate ice-room control board. When the module + inlet valve both test good, the board is the suspect. $345–$485 OEM installed. We always test harness and module first.

Frigidaire ice maker repair in the Twin Cities

Repairs carry a 1-year written warranty.

FAQ

Frigidaire Ice Maker Not Working questions

  • Why is my Frigidaire ice maker not working?

    5 causes in order: freezer too warm, water filter past life, on/off switch bumped off, frozen fill tube, or failed ice maker module / inlet valve. We diagnose in that order on every call.

  • How do I reset a Frigidaire ice maker?

    Slide the wire-bail switch up (off) for 30 seconds, then back down (on). On models with a button, hold for 3 seconds. A reset clears the control but does not fix mechanical failures — you'll still need parts if the module is bad.

  • How long does a new Frigidaire ice maker take to make ice?

    First cycle around 90 minutes from when the freezer hits ≤10°F. First bin full usually 24 hours after install. If it still isn't making ice, we're open 7am-9pm every day and same-day appointments are available.

  • Why are my Frigidaire ice cubes hollow or small?

    Low water pressure at the inlet valve is the usual cause (your install guide lists the minimum supply pressure). Replace the filter first. If still hollow, the inlet valve coil is weak and needs replacement ($185–$245).

  • How much to fix a Frigidaire ice maker?

    Most Frigidaire ice maker repairs run $185–$485 depending on the part: inlet valve $185–$245, ice maker module $245–$425, Professional control board $345–$485. The $149 trip fee is waived when you approve the repair. Sealed-system or compressor work runs higher and we always quote that up front.

Book refrigerator repair in the Twin Cities

Have your model and serial number handy. Same-day appointments are available across the Twin Cities.

Central Minnesota Appliance Repair, 222 E Hennepin Ave, Minneapolis, MN 55414. (651) 364-7466. Open 7am-9pm every day.

Contact us →

Central Minnesota Appliance Repair · Independent appliance repair since 2009 · Open daily 7am to 9pm · (651) 364-7466 · 222 E Hennepin Ave, Minneapolis