Commercial Repair
Walk-In Cooler Temperature: Legal Limit vs Set Point
The TCS food in your walk-in has to be at 41°F or colder, and the walk-in cooler temperature that gets you there is a set point chosen for your unit, not a number written into the law. Kolpak's drop-in cooler systems are factory preset to 35°F, 6°F under the 41°F limit for the food. This page sorts out what the rules say, what a manufacturer publishes and how to read the temperature your walk-in is really holding.

The short answer
- Legal limit for cold food: 41°F (5°C) or below for time/temperature control for safety (TCS) food, under FDA Food Code 2022, section 3-501.16(A)(2). Minnesota's own rule, part 4626.0395, says the same.
- Untreated shell eggs: stored in refrigerated equipment that holds an ambient air temperature of 45°F (7°C) or less.
- Factory set point example: Kolpak's drop-in refrigeration manual says coolers are factory preset to 35°F/2°C and freezers to -10°F/-23°C.
- The limit is on the food. The air reading on the wall tells you how the system is behaving. The probe in the product tells you whether the food is at the required temperature.
- Your local health inspector and your unit's manual decide the finer points. The Minnesota Department of Health notes that some Minnesota cities and counties may have more stringent food codes.
What temperature should a walk-in cooler be?
There are two different numbers, and mixing them up causes most of the confusion.
The first is the legal ceiling. In the FDA Food Code 2022, section 3-501.16(A)(2) requires TCS food to be kept at 5°C (41°F) or less, except during preparation, cooking or cooling, or when time is used as the public health control. That is a limit on the temperature of the food. It is not a recommendation for where to set the controller.
The second is the set point on the walk-in's temperature control. No code picks that number for you. It has to be low enough that the food stays under the ceiling through the whole cycle of the compressor and the defrost. Kolpak publishes one example. Its Drop-In Refrigeration System installation, operation and maintenance manual (part number 550002878-10, 08/21) says "Coolers are factory preset to 35°F/2°C" and "Freezers are factory preset to -10°F/-23°C." The same installation checklist tells the installer to verify or set the temperature control to the desired temperature range. So the factory number is a starting point that the installer confirms for your box.
If your walk-in is a different brand, the number on its controller may not be 35°F. Look in that unit's installation and operation manual, or ask the company that installed it.
What does Minnesota enforce?
Minnesota food businesses, including those in Minneapolis and St. Paul, are held to the Minnesota Food Code, Minnesota Rules chapter 4626. The Minnesota Department of Health says the revised code took effect January 1, 2019, and that some cities and counties in Minnesota may have more stringent food codes. The cold-holding rule is part 4626.0395, titled TCS Food, Hot and Cold Holding and labeled 3-501.16. It requires TCS food to be held "at 41 degrees F (5 degrees C) or below under mechanical refrigeration," and it carries the same 45°F ambient air rule for untreated eggs. Your local health inspector has the final word on how the rule is applied in your kitchen.
How cold should a walk-in cooler be?
Cold enough that every TCS item in it stays at 41°F or below, including the food in the warmest part of the box. The Food Code sets a ceiling and no floor, and we found no manufacturer document that states a lowest setting for a cooler. If you want to run colder than the factory preset, ask the maker of your system or your refrigeration technician whether your unit is built for it. Do not change a set point on a guess.
If you are chasing a number because food is warm, treat it as a repair question. Our walk-in cooler not cooling page lists what to look for.
How cold does a walk-in cooler get?
A walk-in cooler holds close to the set point on its control, and the temperature moves around that number all day. The Kolpak manual describes it this way: in a cooler, the evaporator fans run continuously, even during defrost cycles, and the condensing unit cycles on and off to maintain the walk-in temperature. The same manual says walk-in temperatures rise above the set point during defrost cycles (approximately 30 to 45 minutes, 4 times per day, in the drop-in system manual) and return to the set point once the cycle is complete.
That has two practical effects for a kitchen manager:
- The control works from two values. The Johnson Controls A421 controller in the Kolpak manual uses a "Relay On" (cut-in) and a "Relay Off" (cutout) temperature. The manual says that adjusting just one of them changes the differential between the two, so to keep the differential constant both are moved by the same number of degrees.
- A reading taken during a defrost cycle will be higher than the same display a little later. Log your readings at the same times each day, and ask your inspector how they want the defrost swing documented.
Another Kolpak document, its Refrigeration System Installation and Operation Manual (550006500, August 2018), lists the controller settings "tS" (temperature setpoint) and "diF" (differential) and says the default defrost for its air defrost evaporators is every 6 hours for 30 minutes. Your own unit may differ, so the manual for your model is the reference.
What temp does a walk-in cooler need to be, air or product?
The legal limit applies to the food, and the air and the food can read differently. The Food Code requires food temperature measuring devices to be provided and readily accessible (section 4-302.12(A)), and a small-diameter probe for thin foods such as meat patties and fish filets (4-302.12(B)). Use a probe on the product. It is the reading you can show an inspector.
The thermometer mounted in the walk-in is a separate requirement. Food Code section 4-204.112(A) says the sensor of a temperature measuring device in a mechanically refrigerated unit must be located to measure the air temperature, or a simulated product temperature, in the warmest part of the unit. The FDA's annex to that section explains why. A device in the coldest location "may not be representative of the temperature of the unit," and food could be stored in areas that exceed Code requirements. Minnesota's equivalent is part 4626.0620, which uses the same wording and requires cold holding equipment for TCS food to have at least one integral or permanently affixed temperature measuring device placed so its display is easy to see.
What none of those documents tells us is exactly where the warmest part of your particular walk-in is. That depends on the box, the evaporator and how it is loaded. Ask your inspector or the company that installed the unit. A few things you can do without touching the refrigeration system:
- Keep the evaporator's air supply and return clear. Kolpak's manual says any interruption or obstruction of the supply or return air streams will result in unsatisfactory operation of the system.
- Probe the product itself, not just the air, and write the reading down with the time.
- Compare the wall display to a separate thermometer you trust. If they disagree, tell your technician. The A421 controller in Kolpak's manual has a sensor offset setting of -5°F to 5°F in its advanced menu, and that is a job for the technician.
What can a kitchen change, and what is for a technician?
Operators can log temperatures, keep the door closed, keep the air paths clear and probe the food. Everything on the refrigeration side belongs to a trained technician. Kolpak's manual states that installation and maintenance or servicing are to be performed only by trained and qualified personnel familiar with commercial refrigeration systems. Our technicians hold EPA Section 608 Universal certification.
Call a technician when the display stays above your set point after a full defrost, when food probes read above 41°F, or when the box is icing up. Our post on a walk-in cooler evaporator icing up covers that last one, and the walk-in cooler repair page covers what we handle. For a walk-in cooler drifting warm or not holding temperature, our range is $385–$885 parts and labor. Commercial visits start with a diagnostic of $199–$299 depending on the equipment, waived when you approve the repair. We are open 7am–9pm every day, same-day appointments are available, and completed repairs carry a written 1-year parts-and-labor warranty. We are an independent company and not a manufacturer's service network for any brand, so equipment still under manufacturer warranty should go to the manufacturer's network first. Call (651) 364-7466, or see our wider commercial refrigeration repair page.
FAQ
Is 40°F too warm for a walk-in cooler?
The Food Code limit for TCS food is 41°F or below, so food at 40°F is inside it with 1°F to spare. That is a thin margin once door openings and defrost cycles are added. Kolpak's drop-in cooler systems are factory preset to 35°F, which puts the set point 6°F under the 41°F food limit.
What temperature should a walk-in freezer be?
Kolpak's drop-in system manual says its freezers are factory preset to -10°F/-23°C. The Food Code sets no general storage temperature for frozen food. Section 3-501.11, and Minnesota part 4626.0370, say only that stored frozen food must be maintained frozen, so check your own unit's manual for its set point.
What temperature must eggs be kept at?
FDA Food Code 2022, section 3-501.16(B), and Minnesota Rules part 4626.0395 require eggs that have not been treated to destroy all viable Salmonellae to be stored in refrigerated equipment that maintains an ambient air temperature of 45°F (7°C) or less.
Does my walk-in need a thermometer?
Under Food Code 4-204.112(B), cold holding equipment for TCS food must have at least one integral or permanently affixed temperature measuring device that is easy to view. Minnesota's part 4626.0620 says the same, with an exception for equipment where a device is not a practical way to measure the air around the food.
Who decides how my walk-in is inspected?
Your local health inspector. The Minnesota Department of Health notes that some Minnesota cities and counties may have more stringent food codes, so ask your inspector which rules and logging expectations apply to your kitchen.