Electrolux electric (EFME, EFDE) and gas (EFMG, EFDG) dryers — including Perfect Steam pedestal-base models — lose heat for the same five reasons across the line: heating element, thermal limiter, gas valve coils, igniter, and control board. Electrolux is also strict about vent restriction; the limiter trips fast.
Reviewed by Mike Larson, Master Appliance Technician · 18+ yrs in-field · Last reviewed
Same-day diagnostic
Call before 2pm weekdays.
OEM parts on truck
Brand-specific stocking.
Diagnose before quote
Written, no surprises.
1-yr labor warranty
Parts & labor in writing.
Quick answer
Electrolux dryer no-heat clusters: electric on heating element + thermal limiter (Electrolux's limiter is more sensitive than most — a slightly restricted vent trips it within a few cycles), gas on coils + igniter, and occasionally on a control-board heat relay. Most repairs land $215–$425 all-in. Flat $149 trip fee waived on approval. 1-year warranty.
Root causes, ranked by what we find
What it is: Electrolux's high-limit / one-shot limiter trips earlier than most brands. A vent that's 50% restricted often trips it. Dryer tumbles, no heat.
Fix: Clear full vent run, replace OEM limiter + high-limit kit, verify temp rise.
Typical all-in: $215–$345 all-in
What it is: 240V coil burns open. Tests open. Common at year 5–9 on Perfect Steam units that get heavy use.
Fix: Replace OEM heating element + limiter kit, inspect blower wheel and steam-line fittings.
Typical all-in: $245–$385 all-in
What it is: Coils on gas valve fail — igniter glows, valve doesn't open or drops out.
Fix: Replace OEM coil kit, verify ignition and flame sustain.
Typical all-in: $245–$365 all-in
What it is: Silicon-carbide igniter cracked — no glow, no ignition.
Fix: Replace OEM igniter, verify glow and burn.
Typical all-in: $215–$315 all-in
What it is: Thermistor drift or board relay welded — confirmed in Electrolux service mode.
Fix: Replace OEM thermistor or main board.
Typical all-in: $285–$425 all-in
Diagnostic order
Half-tripped breaker gives a tumble-no-heat symptom. Free fix if that's it.
Disconnect at the wall, run High 5 min. Strong hot air = vent OK; weak / cool = clogged.
Pull rear panel, ohm both. Open = blown by restriction.
8–14 Ω across leads = OK. Open = replace kit.
Glow + no flame = coils. No glow = igniter.
FAQs
Most often a vent restriction tripped the thermal limiter (Electrolux limiters are sensitive — partial vent restriction trips them). Less often a burned heating element or failed gas valve coils. Repair $215–$385 all-in.
Very. Electrolux specifies a maximum 25 ft equivalent vent length and trips the limiter earlier than most brands. We always clean the vent on no-heat calls — skipping it means the new limiter trips in weeks.
Yes — EFLS / EFLW washers and EFME / EFMG dryers in Perfect Steam configurations. Pedestal-base steam lines are extra to inspect on no-heat calls because a kinked line can cause overheat trips.
Same heating system. Stacked install access is tighter; we may charge a small access surcharge if pulling the unit is required.
$215–$425 all-in. Vent + limiter $215–$345, element kit $245–$385, gas coils $245–$365, igniter $215–$315, thermistor / board $285–$425. The $149 trip fee credits to repair.
Yes — heating elements, limiter / high-limit kits, gas valve coils, igniters, thermistors, blower wheels, and main control boards for EFME, EFMG, EFDE, EFDG, and Perfect Steam units.
Related coverage
See all Electrolux repair services.
What will this cost?
Trying to decide repair vs. replace? These pages break down real all-in pricing by brand, model class, and failure mode — so you know the number before we knock.
