Electrolux Error Codes
Washer Codes First, Plus Dryer & ICON Wall Oven — What They Mean
Electrolux (and ICON) shares many control platforms and codes with Frigidaire; confirm by model number. Twin Cities calls cluster on washer E11 / E20 (fill / drain), dryers that do not heat or dry slowly, and ICON wall oven sensor faults.
- 4.5★ · 900+
- 1-Yr Warranty
- OEM Parts
- Same-Day
Same-day windows
Call early for a same-day route.
Serving the Twin Cities
$149 trip fee, credited to repair.
EPA 608 certified
Sealed-system & refrigerant work.
1-year warranty
Parts and labor in writing.
Quick answer
Electrolux Error Code Repair — Twin Cities — Quick Answer
What we fix in the Twin Cities
The Twin Cities repair mix
Washer E11 / E13 / E20
E11 = didn't fill in time — water valve, kinked supply hose, or low pressure. E13 = flood switch tripped (water in the base) — find the leak before resetting. E20 / E21 = drain fault — pump filter clogged is a very common cause; we open and clean it before condemning the pump. $245–$385 typical.
Dryer not heating or drying slowly
Codes vary by dryer model, so send us the exact display and model number. A restricted vent is a common cause of slow drying and overheating, so we clean the duct and check airflow before replacing parts. If the dryer will not heat, we test the heating element and the circuit that feeds it. If it overheats, stop using it. $245–$425 typical.
ICON wall oven F-codes
F10 = runaway temp (sensor or stuck relay — power down at the breaker and call us; this is the unsafe one). F30 = sensor open. F31 = sensor short. Sensor $245–$345. Board $385–$585.
Electrolux repair in the Twin Cities
Our EPA-certified technicians work on Electrolux and ICON appliances regularly. We stock water valves, drain pumps, motor control modules, heating elements, oven sensors, latch motors, and main control boards on the truck. 1-year written parts-and-labor warranty.
Need appliance repair in the Twin Cities? Call 7am–9pm, every day.
FAQ
Appliance repair in the Twin Cities: FAQs
What does E11 mean on an Electrolux washer?
Fill timeout — washer didn't reach the target water level in time. Water valve, kinked supply hose, or low water pressure. $245–$345. The technician confirms the cause before replacing parts.
What does E20 mean on an Electrolux washer?
Drain fault. Clogged pump filter is a very common cause — we open and clean it before condemning the pump. $245–$385. The technician confirms the cause before replacing parts.
What does an Electrolux dryer code mean if it won't heat?
Codes vary by dryer model, so send us the exact display and model number. A dryer that will not heat usually has an open heating element or a failed thermal part, $245–$385 OEM. We always clean the vent at the same time so the new element doesn't fail early. The technician confirms the cause before replacing parts.
Are Electrolux and Frigidaire parts the same?
Often, yes — Electrolux owns Frigidaire and the two share many control platforms and codes, but confirm by model number before ordering a part.
How much does Electrolux repair cost?
Most Electrolux repairs land $245–$525 all-in. Washer drain $245–$385. Dryer heat repair $245–$425. ICON oven sensor $245–$345. Control board $385–$585. The $149 trip fee is credited toward the repair when you approve it.
Related repair pages
- Electrolux appliance repair (hub) →
- Frigidaire washer error codes →
- Frigidaire dryer error codes →
- Frigidaire refrigerator error codes →
- Washer not draining →
- Dryer not heating →
- Oven not heating →
- Appliance repair Minneapolis (hub) →
- Refrigerator repair Minneapolis →
- Washer repair Minneapolis →
- Dryer repair Minneapolis →
- Dishwasher repair Minneapolis →
- Oven repair Minneapolis →
- Sub-Zero repair Minneapolis →
What will this cost?
Pricing & repair-cost pages
Trying to decide repair vs. replace? These pages break down real Twin Cities pricing by brand, model class, and failure mode.
Book appliance repair in the Twin Cities
Have your model and serial number handy. Call early and we can often get you a same-day window across the Twin Cities.
Electrolux washer and oven codes: what they mean and what we check
Electrolux front-load washers and wall ovens share their control platform with Frigidaire, so many of the same codes appear. The codes below are the ones we are confident about. If your display shows something else, send us the exact code and the model number.
| Code | What it means | What we check |
|---|---|---|
| E11 | Washer did not fill to the right level in time | Supply valves open, hoses not kinked, inlet screens, water inlet valve |
| E13 | Water detected in the base of the washer | The leak source: door boot, hoses, dispenser, pump, then the base sensor |
| E20 and E21 | Washer drain problem | Pump filter, drain hose and standpipe, then the drain pump |
| E41 | Washer door or lock problem | Door closes fully, door boot not caught, lock assembly |
| F10 | Oven runaway temperature | Turn the oven off at the breaker; then the sensor and relay |
| F30 and F31 | Oven temperature sensor open or shorted | Sensor resistance and wiring to the control |
Published prices on this page: washer drain $245 to $385, ICON oven sensor $245 to $345, control board $385 to $585. The $149 trip fee is credited toward the repair when you approve it.
What should I do if my Electrolux washer shows E13?
Stop the washer and unplug it. E13 means the machine has found water in its base where none should be, so something is leaking. Running it again can move more water onto the floor.
Look around the door boot, under the detergent drawer area and along both inlet hoses for drips. Check the pump filter at the front bottom, since a loose filter cap leaks. If you find a wet hose connection, tighten it by hand and wipe the base dry. If the code returns after the base is dry, a pump seal or tub leak is likely and we need to look.
Many Twin Cities laundry rooms are in basements. A small leak under a front-loader can run along a concrete floor to the drain, so check behind the machine too.
Can I clear an E20 drain error on an Electrolux washer?
Often. Unplug the washer, open the pump filter door at the lower front, and drain the water into a shallow pan before unscrewing the filter. Remove lint, coins and hair, then reseat the filter fully and close the door. Plug in and run a drain or spin cycle.
If the filter was clean, check that the drain hose is not kinked and that its end is not pushed too far into the standpipe. A pump that hums but does not move water, or does not run at all, needs replacing. Central Minnesota Appliance Repair tests the pump voltage and the wiring before replacing it. Our washer repair page covers other drain symptoms.
Is an F10 on an ICON wall oven an emergency?
Treat it as a safety fault. F10 indicates the oven believes its temperature is running away. Turn the oven off at the breaker, keep the door closed, and let it cool before anyone touches it. Do not use the oven until it has been inspected.
The usual causes are a temperature sensor that reads wrong or a relay stuck closed. Both are tested with the power off and the oven cool. We also check the control board, but only after the sensor and relay.
More Electrolux questions
Why does my Electrolux dryer take two cycles to dry a load?
A blocked vent is the most common reason. Clean the lint screen and the vent run, then see whether the dryer still takes long. Our dryer repair page has more.
Is it safe to leave an E11 washer running?
Stop the cycle and check the supply. An unattended fill fault can leave the machine half filled or leaking.
Where is the Electrolux model number?
On the label inside the door opening or along the lid edge on a washer, and on the oven frame behind the door.