Miele Dishwasher Error Codes
Miele G-series dishwashers (G 5000, G 7000, Professional PG series) display F-codes on the digital panel, and Miele's US support site lists dozens of them. Many of them point to the pump, the water inlet or leak protection. The codes we see most are F11 (drain) and F70 (leak protection). Codes vary by model and generation, so call with your model number for any other code.
Last reviewed November 16, 2026
Quick answer
What do Miele dishwasher error codes mean?
What we fix in the Twin Cities
The Twin Cities repair mix
F11: water left in the wash cabinet
Miele ties F11 to a blocked drain pump, a drain pump cover that is not seated, or, on older G 1xxx to G 6xxx models, a non-return valve installed incorrectly. With the dishwasher off and unplugged, remove the lower rack and rinse the coarse and fine filters in the tub floor, wearing gloves because glass splinters are hard to see in the pump. Miele's support site shows the pump cover steps for your model. If the filters, cover and hose are clean, suspect the drain pump ($325–$525, Miele OEM pumps).
F70: Waterproof system
Miele's Waterproof system protects against leaks, and when it reacts the program is cancelled and the drain pump switches on. Miele's own steps are to close the faucet, switch the dishwasher off and pull the plug, then contact service. Common causes are a door gasket weep, a sump gasket, or a leak at the inlet hose. Stop using the dishwasher until the source is found. We find and replace the leaking part, typically $385–$585 all-in.
Heating faults: sensor, relay and flow heater
Miele lists F1 and F2 (water and heating temperature sensor short or open circuit), F24 (heating relay contact fault) and F25 (desired temperature fault), and calls each a technical fault you cannot remedy yourself. Miele uses an inline flow heater to heat wash water on demand, and mineral scale from hard water can contribute over time. Heater replacement runs $485–$685 OEM.
Miele dishwasher repair in the Twin Cities
We service Miele drain pumps, circulation motors, flow heaters, inlet valves, door switches, WaterProof float assemblies, and door gaskets, and we use genuine Miele parts. 1-year written parts-and-labor warranty.
FAQ
Miele Dishwasher Error Codes questions
What does F11 mean on a Miele dishwasher?
F11 means water is left in the wash cabinet because the drain is restricted: a blocked drain pump, a pump cover that is not seated, or on older models a non-return valve fitted wrongly. Rinse the filters first. If they, the cover and the drain hose are clean, drain pump replacement runs $325–$525 OEM.
What does F70 mean on a Miele dishwasher?
F70 means the Waterproof system reacted and the program was cancelled. Close the faucet, switch the dishwasher off, unplug it and call. We then find and fix the leak path: door gasket, sump gasket, or inlet hose. Typically $385–$585.
Do you use OEM Miele parts?
Yes. We use genuine Miele parts on Miele dishwashers.
How much does Miele dishwasher repair cost?
Most Miele dishwasher repairs land $345–$685 all-in. Drain pump $325–$525. Inlet valve $325–$525. Door gasket $325–$525. Flow heater $485–$685. Circulation motor $485–$685. The $149 trip fee is waived when you approve the repair.
Book dishwasher repair in the Twin Cities
Have your model and serial number handy. Same-day appointments are available across the Twin Cities.
Central Minnesota Appliance Repair, 222 E Hennepin Ave, Minneapolis, MN 55414. (651) 364-7466. Open 7am-9pm every day.
What do Miele dishwasher fault codes mean?
Miele dishwashers show an F code and often a message in the display. The table follows Miele's US support list; codes and wording vary by generation and by whether the model has a text display.
| Code | What it means | Most likely cause | What you can check yourself | When to call |
|---|---|---|---|---|
| F11 | Water is still in the wash cabinet because the drain is blocked. | A blocked drain pump, a pump cover that is not seated, or an incorrectly installed non-return valve on older models. | Switch off and unplug, clean the filters and the pump cover with gloves on, and press the cover down until it clicks. | F11 returns after the filters and cover are clean. |
| F70 (Waterproof system) | The water protection system reacted, so the program was cancelled and the drain pump switched on. | A leak at the door seal, the base or the inlet hose. | Close the faucet, switch the dishwasher off and unplug it; Miele says to contact service. | Every time F70 shows; do not reset and re-run. |
| F12, F13, F15 (water inlet) | The water inlet is blocked or restricted. | A closed faucet, or a soiled inlet filter at the water connection. | Open the faucet fully; the inlet filter needs cleaning with the dishwasher unplugged and the valve housing kept out of water. | The code returns with the faucet open and the filter clean. |
| F14 | The circulation pump is blocked. | A pump that stuck together after weeks or months without running. | Miele's page walks through loosening it with hot water (no hotter than 165 F) and rinse aid; mind the scald risk. | F14 returns after the soak. |
| F1, F2 | The water and heating temperature sensor is short-circuited (F1) or open-circuited (F2). | The temperature sensor or its circuit. | The sensor circuit is not a home repair; note the code and model number. | Whenever shown; Miele calls it a technical fault you cannot fix yourself. |
| F18 | The water intake valve is faulty. | The inlet valve. | Check that the faucet is fully open, then note the code and model number. | Whenever shown, if the faucet is open. |
| F19 | The flow meter (impeller counter) is faulty. | The flow meter. | The flow meter is not user-serviceable; note the code and model number. | Whenever shown. |
| F24 | A heating relay contact fault. | The heating relay or its contacts. | The relay is not user-serviceable; note the code and model number. | Whenever shown, or when dishes come out cool. |
| F25 | A desired temperature fault. | The heating or temperature control circuit. | The control circuit is not user-serviceable; note the code and model number. | Whenever shown, or when the wash water stays cool. |
Typical repair cost for Miele dishwasher faults is $345 to $685; the $149 trip fee is waived when you approve the repair. Drain pump $325 to $525, inlet valve $325 to $525, door gasket $325 to $525, flow heater $485 to $685. Other brands are in the appliance error code library.
What does Miele F11 mean?
F11 is a drain fault. The dishwasher did not empty, so water is still in the cabinet and the control stops the wash. Start by cleaning the filters and checking the drain pump cover and the pump for glass chips or debris.
Common causes of F11:
Glass shard or debris in the drain pump impeller. A single chip from stemware can find its way into the sump and lock the impeller.
Blocked filter housing. Coffee grounds, spinach fibers, small labels off wine bottles.
Drain pump cover not seated. If the cover is not pressed fully home, the pump cannot do its job.
Failed drain pump motor. More likely on older units.
Drain hose or connection problem under the sink, often after a garbage-disposal replacement that left the dishwasher knockout plug in place. Check your installation instructions for the drain-hose requirements for your model.
What does Miele F12 mean?
F12 is a water inlet fault: the dishwasher is not getting the water it expects. Miele's operating instructions pair it with F13 and point first to the stopcock and the inlet filter, so check that the shut-off valve under the sink is fully open before anything else.
Common causes of F12:
Shut-off valve under the sink partially closed. Post-remodel is where this hides.
Soiled inlet filter at the water connection. The inlet hose on a Miele has a valve housing built into it, so this is a job to do with the dishwasher unplugged and the housing kept out of water; if you are not comfortable, book service.
Failed inlet valve (Aqua-Stop). Miele uses a valve built into the Aqua-Stop safety hose.
Failed flow meter. Less common.
What does Miele F70 mean?
F70 means Miele's Waterproof system has reacted to water in the base of the dishwasher. The program is cancelled and the water supply is shut off, so do not ignore it even if the floor looks dry. Close the water shut-off, switch the dishwasher off at the breaker and book service.
Common causes of F70:
Slow gasket seep. A compressed or dried door gasket can drip into the base pan during the wash.
Sump-heater seal failure.
Loose or failed inlet hose to the Aqua-Stop.
Wet base-pan sensor without an active leak, from a prior spill or a nearby plumbing event (the dishwasher often shares a bay with the disposal drain).
How do I fix an F11 fault on a Miele dishwasher?
Start with the filter system in the floor of the tub. Switch the dishwasher off and unplug it, remove the lower rack and spray arm, twist out the filter combination, and rinse it under warm water. Look for glass chips, olive pits, labels and food scraps in the sump, and wear gloves because glass splinters are hard to see. Refit the filters so they lie flat.
Next, press the drain pump cover until its catch engages and it sits flush with the edge, then check the drain hose under the sink for kinks and confirm the garbage disposer knockout plug was removed if the hose connects to a new disposer. If the water still will not leave, the drain pump may be jammed or failing. A pump that hums with no flow, or a cycle that stops partway with water standing in the tub, is a repair call.
Can I reset a Miele dishwasher fault myself?
A simple power cycle is safe: switch it off at the breaker or unplug the machine, wait a couple of minutes, and start a short cycle. If the fault was a one-off, it will not return. Do not open the machine's electrical area, and do not bypass any leak protection.
Leak protection deserves extra caution. If the dishwasher has flagged water in its base, the safe move is to stop using it until the source is found. A leak that is left alone can soak the cabinet and flooring and cost more than the repair.
How to clear a Miele F11 before calling for service
Do this only if you're comfortable pulling the lower rack and filter. If not, skip to booking.
- Switch the dishwasher off at the breaker. Not the button, the breaker.
- Remove the lower rack and the round filter assembly. Turn the filter counter-clockwise.
- Under the filter, locate the drain pump access cover. Open it as shown in your model manual.
- Inspect the impeller. Look for glass, seeds, or debris. Remove any obstruction, wearing gloves because glass splinters are hard to see.
- Refit the filter. Turn it clockwise until it clicks, and press the pump cover down until it clicks.
- Restore power and run a rinse cycle. If F11 returns, it's the pump or the plumbing, so call service.
When should I stop and call instead?
Call instead of repeating the steps above if F11 comes back after the filter and pump cover are clean, if you see or smell water leaking, or if the dishwasher shows F70 at all. Do not open the electrical area, and do not run the dishwasher again after an F70 until the leak path is found: a slow leak can soak the cabinet and the flooring, and that costs more than the repair. A drain problem that traces to the sink plumbing, such as a kinked hose or a clogged disposal, is plumbing work rather than an appliance repair.
The AutoDos wildcard
Miele's AutoDos models add PowerDisk dispensing. A fault on an AutoDos model can be a dispenser problem rather than one of the F-codes above, so read the exact message in the display or manual.
Why do Miele dishwashers run into heating faults in hard-water areas?
Hard water leaves mineral scale on any surface that gets hot. In a dishwasher that means heater components and temperature sensors can scale over, read inaccurately or lose efficiency. Many Twin Cities neighborhoods have hard water, so the dishwasher's water-hardness setting, salt and rinse aid matter more than people expect.
Check the water-hardness setting in the dishwasher's menu against your local water, and keep the salt reservoir filled if your model has one. If the machine still reports heating problems, a technician should test the heater and sensor circuit before parts are replaced.
Is a Miele dishwasher worth repairing?
Usually, because Miele builds these machines to be serviced and parts are available for most models. Central Minnesota Appliance Repair will tell you plainly if a repair is not worth it, such as an older unit with several failing systems. We give the actual quote after diagnosis, before any work starts.
For more on this brand, see our Miele appliance repair page and the dishwasher repair cost guide.
More Miele dishwasher code questions
Why does my Miele dishwasher stop mid-cycle with a fault?
Usually a drain, inlet or leak-protection event. The machine stops when it cannot confirm water is moving correctly. Check the filters and hoses, then call if it repeats.
Should I keep using the dishwasher if only a drying fault appears?
Drying faults are rarely dangerous, but a heater problem can also mean poor cleaning. Hand-dry or run a hot rinse until it is checked.
Do I need to give my model number when I call?
It helps. The number is on the data plate on the door edge. With it we can tell you what to check and what the repair is likely to involve.