Central Minnesota Appliance RepairCMN Appliance
MARSAL · TWIN CITIES

Marsal Pizza Deck Oven Repair in Minneapolis & St. Paul

Marsal pizza deck oven repair in Minneapolis, St. Paul and the Twin Cities, 7am to 9pm daily. Equipment covered: MB Series, SD Series, MB and SD Slice, WF Wave, CT countertop.

Who does Marsal pizza deck oven repair in the Twin Cities?

Central Minnesota Appliance Repair repairs Marsal MB, SD, Slice and WF Wave gas deck ovens and CT countertop electric ovens in Minneapolis, St. Paul and the Twin Cities, 7am–9pm every day. We are an independent company, not an authorized service agency for Marsal. Send a photo of the rating plate. The diagnostic is $199–$299, waived when you approve the repair.

Book a Marsal pizza deck oven diagnostic online or call (651) 364-7466.

Last updated

About Marsal

Marsal builds gas pizza deck ovens in the MB Series (brick-lined), the SD Series in 4, 6 and 8 pie sizes, MB and SD Slice ovens and the WF Wave flame oven, plus the CT-301 and CT-302 electric countertop ovens. Its own site says it is owned and operated as part of the Middleby family under the Blodgett brand umbrella in Essex, Vermont.

On a gas Marsal the rating plate is on the inside wall of the control door area, and we read it before we touch anything. Gas safety parts and thermostat adjustment stay with a qualified technician. For other deck makers see deck oven repair, Bakers Pride and Blodgett.

Marsal equipment we service

Marsal pizza deck oven lines we service and their common failure patterns
Series / linePositioningCommon failures
MB Series (MB 42, MB 60, MB 866)Brick-lined gas deck ovens that need a 15 amp supply for the oven lightSafety pilot valve, thermostat, burner flame, oven light, deck stones
SD Series (448, 660, 866, 1048, 1060, 10866)Gas deck ovens in 4, 6 and 8 pie sizes with 7-inch or 10-inch doorsPilot, thermocouple, safety valve, thermostat, air shutter, draft
Slice ovens (MB 236, SD 236)Gas deck ovens with a 24-inch deep chamberPilot, thermostat, burner, door, deck stones
WF Wave (WF 42, WF 60)Firebrick-lined gas ovens with an open 40,000 BTU side burner and a viewing windowSide-burner ignition, thermostats, flame, window, brick
CT-301 and CT-302Electric countertop deck ovens for two or four 18-inch piesDigital controller, thermostat, heating coils, deck stones

Common Marsal failure patterns

  • Pilot will not stay lit: thermocouple position, draft, a dirty pilot orifice or the safety pilot valve.
  • Burner will not come on with the pilot lit: safety valve, thermostat or a plugged burner orifice.
  • Oven will not throttle down or runs too hot: thermostat capillary, calibration or bypass flame.
  • Floating, lazy flames: too little secondary air from venting, clogged flueways or blocked air inlets. Yellow tips point to too little primary air.
  • Slow recovery or uneven bake: gas pressure, supply line size, extra regulators or draft.
  • Sooting in the chamber: air shutter space too small or clogged with flour dust.

Marsal parts we replace

Common Marsal parts include automatic safety pilot valves, pilot burners and thermostats. Parts are OEM.

  • Automatic safety pilot valves
  • Pilot burners
  • Thermostats
  • Main burners
  • Gas pressure regulators
  • Oven lights

Marsal commercial repair FAQ

Where is the rating plate on a Marsal pizza oven?
On Marsal gas deck ovens the installation manual puts the rating plate on the inside wall of the control door area, and the service manual places it in the control compartment above the light switch. CT countertop ovens carry it on the body back. Send us a photo of the plate with the full model before the visit.
Are you an authorized Marsal service agency?
No. We are an independent company and not an authorized service agency for Marsal. Marsal's warranty runs one year on labor and 18 months on parts, needs service calls authorized by the factory or a Marsal manufacturer's representative, and does not cover equipment serviced by an unauthorized agency. Call Marsal first while that warranty runs. For any other Marsal oven we back our own work for a year.
What is the difference between a Marsal SD 448 and an SD 1048?
Marsal's spec sheet lists both with a 36 by 48 inch cooking surface. The SD 448 has a 7-inch door and the SD 1048 has a 10-inch door, and an SD 1048/SD 448 stack puts the SD 448 on top of the SD 1048. We read the rating plate before we order anything for either model.
Why does my Marsal pilot keep going out?
Marsal's service manual lists a thermocouple off the flame's center, poor or excessive draft, air from a fan or register blowing at the oven front, a low pilot flame, a dirty pilot orifice, a defective thermocouple or safety pilot valve, and a gas leak at the pilot fitting. Gas parts and adjustments are for a technician.
What does Marsal's warranty leave out on a gas deck oven?
Marsal's warranty says ventilation installation, thermostat calibration, air and gas adjustments and safety valve capillary probe adjustments are not covered. It also excludes bricks, fuses, granite shelves, lights, oven faces, broken thermostat capillary tubes and damage from improper draft or gas supply. Ask Marsal or its manufacturer's representative before you pay for a repair you think is warranty work.
How much does Marsal oven repair cost?
Commercial diagnostic is $199–$299 depending on the equipment; it's waived when you approve the repair, and you get a written quote before any repair work. Repairs carry a 1-year parts-and-labor warranty.

What Marsal says it builds and who owns it

Marsal's About page says the company began in 1969 with a small shop at 99 Bowery in New York City and became part of the Middleby family in March 2015. One installation and operating manual (P/N 72614) and one service manual (P/N 72613) cover the MB, SD, Slice and WF gas ovens, and the CT countertop ovens have their own manual (P/N 72615).

Marsal model families and one fact about each

FamilyModelsWhat Marsal's documents say
MB SeriesMB 42, MB 60, MB 866Arched refractory brick-lined ceiling. A 15 amp electrical service is required, and the plug powers the oven light.
SD SeriesSD 448, 660, 866, 1048, 1060, 10866Spring-balanced door. The SD 448 has a 7-inch door and the SD 1048 a 10-inch door.
Slice ovensMB 236, SD 236A 24-inch deep cooking chamber. The SD 236 comes as a single, double or triple.
WF WaveWF 42, WF 60An open 40,000 BTU side burner brings the right side of the chamber over 900°F. Direct venting is not permitted.
CT countertopCT-301, CT-302Electric, with a digital display that reads LOAD before you set the time and DONE when the cycle ends.

Source: Marsal literature page

What Marsal's manual lets an operator do

These are the tasks the operating manual gives to the owner. Anything beyond them is a technician's job.

Clean the deck correctly

On the gas ovens, brush the brick deck and run a wet cloth draped over the brush across it while the chamber is still hot. The CT manual says the opposite: let those stones reach room temperature first, because water soaked into a stone can crack it when heated.

Keep air paths clear

Brush out the combustion compartment weekly. Every six months clean the secondary air ducts and entry ports on the back, and clean around the air shutter so it stays open and free of dust. Setting the shutter is a technician's job.

Use mild cleaners inside

The manual forbids ammonia, lye, soda ash and domestic oven cleaners, which it says damage the aluminum coating. The deck is for pizza and bread only, and other products go in pans.

Know when to stop

The manual requires a complete five-minute shutoff before relighting. If you smell gas, follow the instructions from your gas supplier that the manual says to post. A pilot that will not stay lit is a service call.

Faults the Marsal service manual names

Pilot outages have their own answer in the FAQ above. These are four of the other symptoms in the manual's troubleshooting chart.

SymptomCauses the manual lists
Burner fails to come on with the pilot litBurner valve off, safety valve defective, thermostat out of calibration or defective, burner orifice plugged
Burner will not throttle down or gets too hotBroken thermostat capillary, calibration, minimum bypass flame too high, dirt under the valve seat, defective thermostat
Will not keep up at busy times, or uneven cookingLow gas pressure, undersized supply lines, extra regulators, poor or excessive draft, a fan or register blowing at the oven front
Sooting in the baking or burner chamberAir shutter space too small, or the shutter clogged with flour dust

Source: Marsal gas oven service manual, P/N 72613

What Marsal reserves for qualified service

We list these so you know where the line sits. We do not describe the procedures.

Installation adjustments

Marsal's manual puts thermostat calibration, door and burner adjustments, leveling and gas pressure testing on the installer or dealer, outside its warranty, and says no installation is complete without inspection by qualified personnel.

Gas pressure

The manual lists manifold pressure of 4.5 inches water column on natural gas and 11 on propane for the MB 42, SD 448, SD 1048, MB 60, SD 660 and SD 1060. That is a technician measurement.

CT countertop ovens

The CT manual recommends that all repairs go to a local Marsal service agency, not the owner. We are not that agency, so check warranty status first.

Venting rules in Marsal's manual

A canopy hood needs the short stainless steel flue shipped with the oven. A direct flue needs a draft diverter, class B or better pipe, no more than two 90-degree elbows and a 1 inch per foot pitch on horizontal runs. The gas ovens need 3 to 4 inches at the rear for combustion air, and the manual says pilot outages and floating flames point to too little secondary air. Marsal calls these minimum guidelines, makes ventilation the owner's responsibility and excludes damage from improper ventilation from its warranty. Your local building or mechanical official decides what the system must be.

More questions about Marsal ovens

How do I cure the stones in a new Marsal oven?

The gas manual says to sweep the deck, then run the oven one hour each at 150, 250, 350 and 450°F, with smoke expected on the first heat. The CT countertop manual uses a different schedule that ends at 550°F, so follow the manual for your model.

Why does my WF Wave oven bake hotter on the right?

Marsal's WF instructions say the right side runs about 100°F hotter than the left because of the open side burner. Product facing the flame cooks faster, so turn it. Partly closing the side burner valve reduces top heat.

Central Minnesota Appliance Repair · Independent appliance repair since 2009 · Open daily 7am to 9pm · (651) 364-7466 · 222 E Hennepin Ave, Minneapolis