Same-day Whirlpool dishwasher repair across the Twin Cities — WDF, WDT, WDTA, and KitchenAid-platform KDFE / KDPE / KDTM / KDTE / KDPM. Drain pumps, door latches, circulation pumps, sump leaks, control lockouts. OEM Whirlpool parts on every truck, 1-year written warranty. Part of our full Whirlpool appliance repair coverage.
Same-day service
Calls before 2pm get a today window.
OEM Whirlpool parts
Pumps, latches & boards stocked.
1-year warranty
Parts and labor in writing.
WDF / WDT / WDTA certified
Plus KitchenAid platform.
Why a specialist
Whirlpool dishwashers share a sump-and-pump architecture across WDF, WDT, WDTA, and the KitchenAid-platform KDFE / KDPE / KDTM / KDTE / KDPM units. That means one set of OEM parts — drain pumps, circulation pumps, door latches, sump assemblies, vent-fan housings — covers the bulk of every Whirlpool dishwasher in the Twin Cities. Every truck carries them.
We also know the F-code map and the click-count diagnostics for older units where the Clean LED flashes a count instead of showing a code. Standing-water calls and won't-start calls are 70% of our dishwasher work; both typically finish in a single visit.
Common repairs
The single most common Whirlpool dishwasher call. Drain pump motor failure or a stuck check valve in the sump on WDF, WDT, and WDTA units. Symptom: dirty water sitting in the bottom at the end of the cycle. We replace the OEM Whirlpool W11084655 / W10348269 drain pump and inspect the sump check valve in one visit.
Door latch assembly and the two microswitches inside it fail and the control board can't confirm the door is closed — dishwasher won't start the cycle. We replace the OEM door-latch assembly (latch + both switches as a unit) and reset the control.
Circulation pump bearing or impeller failure on WDT and WDTA units. Symptom: cycle completes but dishes come out with food still on them, or you hear the spray arms barely turning. We replace the OEM circulation pump motor and check the spray-arm bearings.
Whirlpool dishwasher main control boards on WDF and WDT units lock up — buttons unresponsive, lights flashing, or heated dry stuck on while wash cycle never starts. We carry the most-failed Whirlpool W10854227 / W10854231 boards on every truck and verify the door-latch and harness before swapping.
Water under the dishwasher is almost always the lower spray arm support seal, the sump-to-tub gasket, or the door gasket. We pull the unit, identify which seal is failing, and replace with OEM parts in one visit. We also check for the well-known WDF / WDT vent fan housing crack that drips water down the front of the door.
Water inlet valve solenoid sticks closed (no fill, dry cycle) or the overfill float sticks up (cycle won't start). We replace the OEM inlet valve and inspect the float assembly in one visit.
Reference
| Code | What it means | What to do |
|---|---|---|
| F2 | Door latch / open during cycle | Call us — latch + microswitch assembly |
| F3 | Heating element / thermistor fault | Call us — element diagnostic |
| F5 | Spray-arm / motor fault | Call us — circulation pump diagnostic |
| F6 | Water inlet — no fill in time | Check house water supply; call if cleared and recurs |
| F7 | Flow meter fault | Call us — needs a tech |
| F8 | Turbidity sensor fault | Call us — sensor or board diagnostic |
| F9 | Diverter motor fault | Call us — needs a tech |
| FE | Communication fault between control boards | Call us — board diagnostic |
| Clean LED flashing | Generic fault code — count flashes per pause | Call us — we'll decode on the visit |
| Heated dry stuck on | Main control board failure | Call us — board replacement |
Coverage
Field-tested
Service area
Transparent pricing
Circulation pump rebuilds are quoted only after we confirm spray-arm wear isn't the real cause. We won't pull a dishwasher for a pump job we don't need.
FAQ
Standing water at the end of a cycle is almost always the drain pump or a stuck sump check valve. About 75% of standing-water calls are a drain pump failure (motor seized or impeller fouled); the rest are a check valve stuck open / closed in the sump assembly. We carry the OEM Whirlpool drain pump on every truck and finish most standing-water calls in 60–90 minutes.
Three usual suspects: the door latch / microswitch (F2 code — control can't confirm the door is closed), a stuck overfill float (cycle starts then immediately stops), or a main control board lockout (buttons unresponsive, lights flashing). We diagnose all three on the first visit and finish 75% of won't-start calls in one trip.
Most Whirlpool dishwasher repairs land between $189 and $465 all-in (parts and labor) with our 1-year written warranty. Drain pumps $225–$345; door latch + microswitches $215–$295; water inlet valve $189–$285; control board $285–$465. Circulation pump rebuilds are the exception — $345–$525 and a longer job because we have to pull the dishwasher to reach the sump.
Three culprits in order of likelihood: a worn circulation pump impeller (spray arms barely turning), a clogged spray-arm bearing (arms not rotating at full speed), or a turbidity sensor failure (cycle ends early thinking the water is clean). All three we test on the first visit. We also check the chopper screen in the sump — large food debris there is a sign the chopper assembly has failed.
Yes — KitchenAid KDFE, KDPE, KDTM, KDTE, and KDPM dishwashers share most of their internals with Whirlpool WDTA. Same drain pumps, same circulation pumps, same control boards. We service all of them with OEM parts on the truck.
Calls placed before 2pm on a weekday typically get a same-day window across the Twin Cities and Central MN. Drain pumps, door latches, inlet valves, and the most-failed control boards are stocked on every truck — most calls finish in one trip.
Essentially every Whirlpool dishwasher from the last 15 years — WDF (520/540/560/730/750/760/775), WDT (720/730/750/780/970/975), premium WDTA (50/75/80/95), and the KitchenAid-platform KDFE / KDPE / KDTM / KDTE / KDPM units. Bring the model number sticker (inside the door, on the tub rim).
Same-day windows when you call before 2pm weekdays. OEM Whirlpool parts, 1-year warranty, full WDF / WDT / WDTA + KitchenAid platform coverage.
