Kenmore Washer Error Codes
Kenmore is a retail brand, not a manufacturer, so there is no single Kenmore washer code list: your washer was built by Whirlpool (model prefix 110), LG (796), Samsung (592) or Frigidaire (417), and the first three digits of the model number tell you whose codes apply. This page lists only codes verified on Whirlpool's, LG's and Samsung's own support pages.
Last reviewed November 16, 2026
Quick answer
What do Kenmore washer error codes mean?
What we fix in the Twin Cities
The Twin Cities repair mix
Find your Kenmore model number prefix first
Open the door (front-load) or lift the lid (top-load) and find the model/serial plate. The first three digits are the manufacturer code. 110 = Whirlpool, 796 = LG, 592 = Samsung, 417 = Frigidaire. Knowing the platform lets us identify the right parts. We could not confirm a public code list from Frigidaire for washers with model numbers starting 417, so none are listed here.
Most common Kenmore washer codes (Whirlpool platform, 110.*)
F21 or F02 = the washer took longer than expected to drain: a kinked or clogged drain hose, non-HE detergent or a blocked pump filter. LF = long fill: check that both supply faucets are fully open. Sd / Sud = excessive suds detected: use HE detergent and follow the dosing line on the cap, using less for small loads. For the full Whirlpool-platform list, see our Whirlpool washer error codes page.
Kenmore washer repair in the Twin Cities
We work with Whirlpool, LG, Samsung and Frigidaire parts, whichever platform built your Kenmore: inlet valves, drain pumps, pressure sensors, door locks, suspension springs, shifters and actuators, motor control boards and main control boards. 1-year written warranty.
FAQ
Kenmore Washer Error Codes questions
Who makes Kenmore washers?
Kenmore is a Sears brand, not a manufacturer. Your washer was built by Whirlpool, LG, Frigidaire, or Samsung. The first three digits of the model number identify the manufacturer: 110 = Whirlpool, 796 = LG, 417 = Frigidaire, 592 = Samsung.
What does F02 mean on a Kenmore washer?
On a Whirlpool-built Kenmore (model prefix 110), F02 and F21 both mean the washer drained more slowly than expected. Unplug the washer for about five minutes, check the drain hose for kinks and clear the pump filter. Drain pump replacement runs $225–$345 if the code returns.
What does Sd or Sud mean on a Kenmore washer?
Excessive suds were detected, so the washer extends the rinse to clear them. Use HE detergent (look for the HE logo on the bottle) and follow the dosing line on the cap, using less for small loads. If the code repeats with correct detergent use, have the washer checked.
How do I find my Kenmore model number?
Front-load: open the door, look at the inside frame. Top-load: lift the lid, look at the rear of the opening. The model number is usually formatted XXX.XXXXXXX, and the first three digits tell us the manufacturer.
How much does Kenmore washer repair cost?
Most Kenmore washer repairs land $245–$485 all-in. Drain pump $225–$345. Inlet valve $220–$320. Door lock $185–$285. Pressure sensor $225–$325. Shifter / actuator $285–$425. Main control board $385–$585. The $149 trip fee is waived when you approve the repair.
Book washer repair in the Twin Cities
Have your model and serial number handy. Same-day appointments are available across the Twin Cities.
Central Minnesota Appliance Repair, 222 E Hennepin Ave, Minneapolis, MN 55414. (651) 364-7466. Open 7am-9pm every day.
Why do Kenmore washers show different codes for the same problem?
Kenmore is a retail brand, and the washers sold under it have been built by several manufacturers. The same fault, such as a washer that will not drain, can appear as one code on a Whirlpool-built Kenmore and a different code on an LG-built Kenmore. The model number on the label tells you whose code chart applies. For other brands, see the appliance error code library.
At Central Minnesota Appliance Repair we start every Kenmore washer call by reading the model number, because the wrong chart leads to the wrong part. Look for the label inside the door frame on a front-loader, or around the lid opening on a top-loader.
Kenmore washer codes by who built the machine
Only codes verified on the builder's own support pages are listed: Whirlpool for model numbers starting 110, LG for model numbers starting 796 and Samsung for model numbers starting 592. Model prefixes are a guide; if your label does not match, give us the full model number.
| Code | What it means | Most likely cause | What you can check yourself | When to call |
|---|---|---|---|---|
| F21 or F02 (Whirlpool-built, 110.) | The washer drained more slowly than expected. | A kinked or clogged drain hose, non-HE detergent, excess suds, a blocked pump filter, or a drain hose set too high. | Unplug the washer for about five minutes, plug it in and reselect the cycle; check the drain hose for kinks. | Call if the code returns after the hose and filter are clear. |
| LF (Whirlpool-built, 110.) | The washer is taking too long to fill. | A partly closed supply faucet, or a drain hose pushed too far into the standpipe causing siphoning. | Check that both hot and cold faucets are fully open and the drain hose sits no more than about 4.5 inches into the standpipe. | Call if LF returns with the supply fully open. |
| Sd or Sud (Whirlpool-built, 110.) | Too many suds were detected; the washer extends the rinse to clear them. | Too much detergent, non-HE detergent, or certain liquid chlorine bleaches. | Use HE detergent, follow the dosing line on the cap and let the cycle finish. If it shows after the cycle ends, rinse the load again. | Call if it repeats with correct detergent use. |
| OE (LG-built, 796.) | The washer cannot drain the water from the wash. | A kinked drain hose or a clogged drain pump filter. | Unplug the washer, clear the drain filter with towels down and straighten the hose. | Call if OE returns after cleaning, or after a tub clean cycle. |
| IE (LG-built, 796.) | The tub did not fill to an adequate level in the set time. | A closed faucet, a kinked inlet hose or a clogged inlet filter. | Open both taps fully, straighten the inlet hoses and clean the inlet screens. | Call if IE returns with good water pressure. |
| UE (LG-built, 796.) | The load is unbalanced in the drum. | A load that is too large or too small, or a washer that is not level. | Redistribute the clothes and check that the washer is level. | Call if UE repeats on balanced, level loads. |
| dE (LG-built, 796.) | The door is not closed or not locking (dE1 not closed properly, dE2 closed but not locked). | A door not latching, or a door lock that is failing. | Unplug the washer for 10 seconds, plug it in and restart with the door fully closed. | Call if dE persists with the door closed. |
| 5E (Samsung-built, 592.) | A water drainage problem. | A clogged drain pump filter or a kinked or blocked drain hose. | Clean the drain pump filter and check the drain hose for kinks and blockages. | Call if 5E returns after cleaning. |
| 4E (Samsung-built, 592.) | A water supply problem. | A closed tap, a blocked or kinked supply hose or a clogged inlet mesh filter. | Open the tap fully and check the supply hose and inlet mesh filter. | Call if 4E returns with water flowing. |
Typical Kenmore washer repair cost is $245 to $485; the $149 trip fee is waived when you approve the repair.
What should I do first when my Kenmore washer shows a drain code?
Start with the drain filter. On a front-load Kenmore it sits behind a small access panel at the lower front. Unplug the washer, put towels and a shallow pan down, release the small drain hose to let the water out, then unscrew the filter and clear out coins, lint and hair. Reinstall it fully tight so it does not leak.
Then look at the drain hose behind the machine. A kink, a hose pushed too far into the standpipe or a missing high loop can all slow drainage. If the code returns after both checks, the drain pump is the next suspect. See Whirlpool washer error codes, LG washer error codes and Samsung washer error codes for the platform-specific lists.
How much detergent should a Kenmore front-load washer use?
Much less than most people use. High-efficiency washers use little water, so extra detergent does not rinse out and builds up as suds. That is what triggers the suds code on Whirlpool-built models. Use detergent labeled HE, follow the dosing line on the cap for a normal load and use less for light loads.
If suds are already in the tub, run a rinse cycle with no detergent and let the washer finish. Repeated suds codes with correct detergent use may point to a drain or pressure-sensing problem, which is worth a service visit.
What about Frigidaire-built (417.) Kenmore washers?
We could not confirm a public code list from Frigidaire for Kenmore washers with model numbers starting 417, so none are listed here. Check the code list in your manual, or call us with the full model number. See our Frigidaire washer error codes page for the brand's own washers.
What drives Kenmore washer repair prices in the Twin Cities?
Kenmore washer repairs typically land in the $245 to $485 range all-in, depending on the part and the platform. The $149 trip fee is waived when you approve the repair, and the work carries a 1-year written parts-and-labor warranty. Our Kenmore appliance repair page covers other Kenmore appliances, and the washer repair page covers common washer problems across brands.
Kenmore washer code questions
Is my Kenmore washer the same as a Whirlpool?
If the model number starts with 110, it was built by Whirlpool and uses the Whirlpool code set. Other prefixes mean a different manufacturer.
Can I read a code history on my Kenmore washer?
Some models have a diagnostic mode, but the key sequence differs by platform. Check your owner's manual or ask us to run it during a visit.
My Kenmore washer stops mid-cycle with no code. What now?
Check that the door or lid is closed, the load is balanced and the washer is level. If it keeps stopping, a technician should check the door lock, lid switch and drain.